CORDONA PQ8 236 Combo Quickshifter, Stand-Alone Quickshifter for BMW S1000RR 2009-2014

Product Details

Cordona 236 PQ8 Combo Quickshifter, stand-alone quickshifter kit consisting of module, sensor, wiring harness and shift rod (160 mm), for BMW S1000RR, Type K10, model year 2009-2014

General Description

Electronic full throttle upshifts, seamless acceleration - whether for racing motorcycles, streetn motorcycles, drag bikes, go-karts, cross-karts - essentially anything with a sequential transmission. The PQ8 does not trigger an error message in engines with fuel injection. The PQ8 has been developed with the latest technology and is continuously optimised through its use in worldwide racing series.

Features:
- Stand-alone system: no further accessories are required.
- Easy to reverse.
- Supplied with a universal shift rod (6 mm internal thread). This may need to be shortened to the correct length depending on the footrest system used. Other shift rods of different lengths are available, see accessories.
- Built on advanced GP technology and fully computer-controlled via a 20 MHz CPU. Programming via a 2 tip switch system.
- Compu Shift calculates the perfect interruption time for each individual upshift. From a selection of 500 interruption times, various engine ratios, acceleration, load and engine speed are taken into account depending on the riding conditions. The interruption time is adjustable between 40-80 milliseconds.
- Simulates stable engine operation to the ECU during the shifting process, thus allowing for a smooth and stable upshift. No error messages are generated, and it does not lead to unintended lean or rich mixture formation.
- Integrated “Smooth Shift” to reduce load peaks on the transmission and chain. In addition, power loss during upshifts is minimised, similar to MotoGP quickshifters. During the shifting process, all cylinders are simultaneously shut off, and power re-engagement occurs via a computer-controlled sequence in conjunction with Compu Shift.
- Solid, waterproof housing and high-quality wiring harness. The circuit board is fully potted and equipped with a 26-pin aviation standard connector.
- Very high-quality sensor based on strain gauge technology.
- Sensor works on push and pull, so it can also be used for reverse shifting.
- All functions can be easily and conveniently programmed directly at the racetrack or on tour, without an additional device, using two buttons and the LED display.
- Supplied with ready-to-use connectors for Denso and Mitsubishi ignition coils, which are used in most Japanese sports motorcycles, as well as vehicles from Triumph and KTM [For KTM Superduke R 2008, Beru ignition coils are installed; please use the wiring harness for Ducati 749 here]. For Ducati 748-998, 749-1198, Aprilia RSV 4, MV Agusta 2 and 4 ignition coils, corresponding wiring harnesses are available through the Cordona distribution network. For other ignition coil systems, installation is not “plug and play”, but remains uncomplicated.
- For vehicles with coil-on-plug ignition coils, the +12V power supply comes from the ignition coil via the red cable, which leads directly to the CPU of the PQ8 quickshifter. Simple installation, as additional cable installation for 12V power supply is not required.
- Automatic on/off switching controlled by speed. Fully adjustable to prevent unwanted engine shutdown by shifting into neutral during idle speed.
- Audible signal generator for acoustic feedback during functional tests and commissioning. Very useful when installed behind fairings.
- Auto Shift, for “drag racing” only, can be selected to automatically activate the quickshifter at a specific and adjustable speed. The rider only needs to keep the shift lever preloaded between shifts. Useful in “handicap” races where the rider must stay under the “break out” time. The shift RPM can also be lowered to deliberately be slower in subsequent races.
- Power saving: if no input is made via the PQ8 display for 60 seconds, the electronics enter power-saving mode. A blinking dot then indicates that the system is ready. Very useful if a battery pack is used to power the quickshifter. The majority of power consumption for the PQ8 display is eliminated.
- Made in Sweden.